فهرست مطالب

فنی و مهندسی مدرس - پیاپی 37 (پاییز 1388)

فصلنامه فنی و مهندسی مدرس
پیاپی 37 (پاییز 1388)

  • مهندسی مکانیک
  • تاریخ انتشار: 1388/11/10
  • تعداد عناوین: 13
|
  • مهدی معرفت، مصطفی خسروی الحسینی صفحه 1
    افت حرارت تشعشعی یکی از بارزترین افتهای حرارتی یخچالهای ویترینی است و روش های مختلفی برای کاهش افت حرارت تشعشعی اینگونه یخچالها پیشنهاد شده است. استفاده از شیشه های چندجدار پر شده با گاز آرگون یا استفاده از مواد شفاف دارای ضریب عبور پایین در محدوده مادون قرمز، از جمله راه حلهای پیشنهاد شده است. برای آنکه به اهمیت موضوع افت حرارت تشعشع نسبت به سایر افتهای ناشی از ورود هوا، افت حرارت هدایت و افتهای ناشی از تجهیزات جانبی سیکل تبرید پی برده شود، مدلسازی انتقال حرارت تشعشع ضروری است. به این منظور از مدل سه بعدی با هندسه خاص یخچال ویترینی ایستاده و فرض همدما بودن سطوح داخلی یخچال در بررسی انتقال حرارت استفاده شده است. یخچال مورد نظر برای نگهداری لبنیات و نوشیدنی ها استفاده شده و سطح اواپراتور آن در وجه فوقانی قرار گرفته است. همچنین برای تعیین خصوصیات تشعشعی وجه شفاف از مقادیر ضریب جذب و عبور شیشه واقعی استفاده شده است.
    نتایج به دست آمده نشان می دهد که کاهش درجه حرارت داخل یخچال، باعث افزایش افت حرارت تشعشعی می شود. در این خصوص درجه حرارت وجه شیشه ای تاثیر نسبتا ناچیزی بر این انتقال حرارت دارد. همچنین افزایش ضریب جذب سطح اواپراتور باعث افزایش انتقال حرارت تشعشع به آن سطح می شود که از آن می توان برای بهبود طراحی استفاده کرد. شار حرارتی تشعشعی هر یک از سطوح در مقایسه با انتقال حرارت جابه جایی آن سطح مقایسه شده که با توجه به میزان آن، استفاده از پوششهای کدر برای مواقعی که از یخچال ویترینی استفاده نمی شود، پیشنهاد شده است.
    کلیدواژگان: یخچالهای ویترینی، اتلاف حرارت، تشعشع، راندمان
  • مجیدعلی طاولی، ابوالفضل درویزه، علی اصغر پاشایی، رحمان یوسفی مقدم صفحه 15
    در این تحقیق شیوه جدیدی برای شکلدهی ورقهای فلزی به روش انفجار مخلوط گازها ارائه شده است که در آن ورق فلزی تحت اثر شوک فشار ناشی از انفجار با سرعت بالا، تغییر شکل پلاستیک پیدا می کند. سامانه شکلدهی برای اولین بار در کشور طراحی و ساخته شده و مشتمل است بر مخزن استوانه ای شکل جدار ضخیم، قالبهای شکلدهی و متعلقات لازم برای اندازه گیری. در این روش، شکلدهی بدون نیاز به سمبه انجام می شود و می توان ورقهای با ضخامت اولیه مختلف را به شکلهای متنوعی برای کاربردهای مختلف مهندسی تبدیل کرد. نتایج تجربی مربوط به اثر پارامترهایی نظیر درصد مخلوط گاز، ضخامت ورق، شرایط مرزی و جنس ورق بر توزیع کرنش محیطی و کرنش ضخامتی، ارائه می شود. همچنین مدلی تحلیلی بر اساس محاسبه کار پلاستیک، برای تغییر شکل ورق پیشنهاد شده است.
    کلیدواژگان: ورقهای فلزی، شکلدهی مخروطی، شکلدهی با سرعت بالا، انفجار مخلوط گازها
  • مهران محبوب خواه، محمد جواد ناطق، سیامک اسماعیل زاده خادم صفحه 29
    در تحقیق حاضر تمامی نیروهای اصطکاکی، اینرسی و ماشینکاری که ممکن است بر میز هگزاپاد ماشین فرز وارد شوند در نظر گرفته شد و با تحلیل نیوتن - اویلری اجزای سازه میز هگزاپاد، بررسی کاملتری از دینامیک انجام شده است. این تحلیل توسط برنامه سازی نوشته شده در محیطMATLAB اجرا و نتایج آن با مقایسه با منابع دیگر تایید شده است. تاثیر نیروهای مختلف در فرایند فرزکاری ای که روی میز هگزاپاد ماشین فرز قرار گیرد نشان داده شده است. این تحلیلها به طراح ماشین ابزار کمک کند که نقش هر یک از عوامل ثر بر عملکرد ماشین ابزار را شناسایی کرده و وزن لازم را به بارهای وارده تخصیص دهد.
    کلیدواژگان: ماشین ابزار، هگزاپاد، دینامیک معکوس، ربات موازی، سازوکار استوارت
  • مهدی معرفت، امیر امیدوار صفحه 39
    در بسیاری از موارد ساکنان ساختمان در فصل زمستان از احساس سرمای موضعی در ناحیه مچ پا و پشت گردن شکایت دارند. در چنین شرایطی افراد برای غلبه بر احساس سرمای موضعی، دمای هوای اتاق را افزایش می دهند و این به معنای افزایش مصرف انرژی است. در ساختمانهای مسکونی با تهویه طبیعی، رخداد پدیده سرمایش موضعی به دلیل وجود پنجره ها و سطوح سرد در ساختمان است. سرعت متوسط و شدت اغتشاش جریان هوا، دو عامل عمده در ایجاد کوران یا سرمایش موضعی ناخواسته است. بیشتر نارضایتی های گزارش شده ناشی از پدیده سرمایش موضعی، در مواردی رخ داده که سرعت متوسط جریان نیز از حد مجاز تجاوز نکرده است. این بدین معنا است که شدت اغتشاش جریان هوا نیز نقش مؤثری در رخداد این پدیده دارد. لذا بررسی پدیده کوران یا سرمایش موضعی ناخواسته در سامانه های گرمایش از کف ساختمان نیز خالی از اهمیت نیست، هر چند در این موارد، سرعت متوسط جریان هوا ناچیز است. در این مقاله به بررسی اثر اندازه پنجره بر ایجاد نارضایتی حرارتی ناشی از پدیده سرمایش موضعی در ساختمانهایی که از سیستمهای گرمایش از کف استفاده می کنند، پرداخته شده است. بررسی ها نشان می دهد که اگر چه اندازه پنجره بر گستردگی محدوده نارضایتی ایجاد شده به دلیل پدیده سرمایش موضعی، مؤثر است، اما این تاثیر به حدی نیست که میزان نارضایتی از مقادیر مجاز استاندارد فراتر رود. بنابراین تبعات نامطلوب ناشی از پدیده کوران یا سرمایش موضعی بر مصرف انرژی، در ساختمانهایی که از سامانه های گرمایش از کف استفاده می کنند چندان چشمگیر نیست. در پایان، محدوده ایجاد نارضایتی در نزدیکی پنجره در دو حالت گرمایش از کف و گرمایش به کمک پانلهای عمودی مقایسه شده است. بررسی ها نشان داد که سیستمهای گرمایش کفی نسبت به پانلهای عمودی از نظر مصرف انرژی و آسایش حرارتی عملکرد بهتری دارند.
    کلیدواژگان: گرمایش از کف، مصرف انرژی، آسایش حرارتی، کوران، سرمایش موضعی
  • رضا کریمی، مجید میرزایی * صفحه 51

    این تحقیق به تحلیل رشد ترک در لوله جدار نازک به روش المان محدود می پردازد. لوله موردنظر حاوی ترک اولیه سطحی در راستای محوری است که تحت بارگذاری انفجاری گازی قرار دارد. بارگذاری انفجاری به صورت شوک داخلی موضعی با فشار بیشینه 6 مگاپاسکال است که با سرعت 4/2 کیلومتر بر ثانیه در طول لوله حرکت می کند. حل عددی پاسخ سازه ای به بارگذاری، توسط WARP3D، که نرم افزاری تحقیقاتی برای تحلیل سه بعدی مکانیک شکست غیرخطی دینامیکی به روش المان محدود است، انجام و از معیار CTOA به عنوان پارامتر شکست برای شبیه سازی رشد ترک در لوله جدار نازک استفاده شده است. در این تحقیق رشد ترک در بارگذاری های مختلف شبه استاتیک نیز شبیه سازی شده است. بخش آخر به مقایسه نتایج حاصل از شبیه سازی رشد ترک به روش عددی و نتایج حاصل از آزمایشهای تجربی که در مطالعات سایر محققان موجود است، می پردازد و اثر تحلیل کامل دینامیکی در رشد ترک در مقایسه با تحلیل استاتیکی ارائه می شود.

    کلیدواژگان: لوله انفجار، پاسخ الاستودینامیک، المان محدود، رشد ترک، WARP3D، بارگذاری متحرک
  • غلامحسین لیاقت، حبیب الله سرایلو صفحه 73
    ساختار پانل های لانه زنبوری متشکل از سلول های شش ضلعی میان تهی است که دیوار آنها به خلاف سایر پانل های ساندویچی، عمود بر صفحات پوسته قرار می گیرد و طراحی آنها اغلب بر مبنای وزن کمینه انجام می شود. در این مقاله، ابعاد هسته لانه زنبوری به گونه ای محاسبه شده تا کمترین وزن را داشته باشد. بهینه سازی وزن نسبت به بارگذاری از دو روش تحلیلی و عددی انجام شده است. بهینه سازی عددی به روش برنامه ریزی درجه دوم متوالی انجام شده است. پارامترهای هندسی و وزن بهینه برای دو مقطع شش ضلعی و چهارضلعی محاسبه و وزن بهینه ناشی از آنها مقایسه شده است.
    کلیدواژگان: سازه لانه زنبوری، وزن کمینه، پانل ساندویچی، بهینه سازی عددی، برنامه ریزی درجه دوم متوالی
  • پرویز رهنما، امیر عبدالله زاده، محمدعمار مفید صفحه 83
    در این تحقیق ضمن مطالعه شکلدهی لوله فولادی جنس D6AC به روش فلوفرمینگ مستقیم، به منظور بررسی تاثیر پارامترهای مختلف عملیات حرارتی بر خواص قطعه، چرخه های مختلف عملیات حرارتی طراحی شده و خواص مکانیکی و تغییرات ریزساختار پوسته فلوفرم شده، مورد بررسی قرار گرفته است. بدین منظور از دماهای آستنیته 850، 900 و C950 برای زمانهای 15 و 30 دقیقه و سرد کردن در C510 به مدت 10 دقیقه و سپس سرد کردن در روغن C60 استفاده شده است. بازگشت اولیه به مدت 2 ساعت در C250 و بازگشت نهایی به مدت 2 ساعت در دماهای 250، 300، 350 و C450 انجام شد. بررسی ها نشان می دهد که چرخه عملیات حرارتی بهینه، آستنیته کردن در C850 به مدت 30 دقیقه و بازگشت نهایی در C300 است، زیرا علاوه بر ایجاد استحکام بالا و چقرمگی شکست مناسب، به دلیل ریزدانه بودن آستنیت اولیه، ویژگی های نرمی آن نیز مطلوب است.
    کلیدواژگان: عملیات حرارتی، فولاد، فلوفرمینگ، اسپینینگ، D6AC، سرد کردن
  • بهزاد قدیری، مانی رازی، صباح حمیدی صفحه 93
    در این مقاله تحلیل آیروالاستیک خطی بال پسگرا در حوزه زمان با دو درجه آزادی در جریان تراکم ناپذیر مورد بررسی قرار می گیرد. معادلات حرکت بال الاستیک، با در نظر گرفتن آن به صورت تیر یک سر درگیر و با استفاده از معادلات لاگرانژ در حوزه زمان استخراج شده و اتصال بال در ریشه، صلب فرض شده است. با در نظر گرفتن مودهای ارتعاشی تیر یک سر درگیر و با به کار گرفتن تئوری نوارهای باریک، نیروها و ممان های آیرودینامیکی وارد شده به بال پسگرا در جریان سیال پتانسیل غیر دائم و تراکم ناپذیر به دست آمده است. معادلات آیروالاستیک به صورت بی بعد استخراج و به روشی عددی حل شده است. نتایج حاصل از روش به کار رفته برای چند بال پسگرای مورد مطالعه، با نتایج تجربی و دیگر مراجع مقایسه شده و تطابق مناسبی بین آنها مشاهده شده است.
    کلیدواژگان: آیروالاستیسیته خطی، بال پسگرا، حوزه زمان، روش مودهای فرضی، فلاتر
  • بهروز فرشی، محمدحسین فائزی صفحه 107
    در صنایع هوافضا، برای دیسکهای توربین گاز، کاربردهای متعددی مانند استفاده در موتورهای توربوجت تعریف شده است. این دیسک های دوار معمولا در شرایط عادی در دمای بسیار بالایی کار می کنند و با سرعت زاویه ای بسیار زیادی می چرخند. لذا کم کردن وزن آنها در دستگاه های مرتبط با صنایع هوافضا، مزایای زیادی دارد و علاوه بر کاهش وزن خالص دستگاه، صرفه جویی اقتصادی را نیز در پی خواهد داشت. در حالت کلی دیسک دوار به علت کاربردهای فراوانی که در صنعت دارد، از دیرباز، موضوع تحقیقات و مطالعات متعددی بوده است. از میان کاربردهای دیسک دوار می توان به دیسکهای توربین و کمپرسورهای توربین های گازی اشاره کرد. دیسک توربین گاز اغلب در گرادیان های دمایی بالا و سرعتهای زاویه ای زیاد کار می کند. سرعت زاویه ای بالا باعث ایجاد نیروی گریز از مرکز بزرگ در دیسک می شود و همزمان با آن، دمای بسیار زیاد، منجر به کاهش مقاومت ماده سازنده دیسک و این باعث افزایش تغییر شکل در دیسک می شود.
    به منظور تحلیل دیسک و رسیدن به توزیع مناسب تنشها در آن، باید با توجه به شرایط دمایی دیسک، خواص ماده را نیز متغیر درنظر گرفت که این تغییرات ممکن است وابسته به شعاع، دما یا هر دو باشد. برای رسیدن به این هدف، دیسک غیرهمگن با ضخامت مشخصی مطالعه می شود. در اینجا، با استفاده از مدل سازی دیسک دوار به عنوان مجموعه ای از حلقه های مختلف که هر یک خواص ثابتی دارند، مساله تغییرات خواص در کل دیسک را با کمی تقریب و با وجود تغییرات در خواص هر یک از حلقه ها نسبت به دیگری، می توان مدل سازی کرد. حالت بهینه و پروفیل آن، با متناسب شدن ضخامت حلقه ها نسبت به هم به دست می آید و محدودیتهای تنش را ارضا می کند. در این تحقیق با استفاده از الگوریتم سیمپلکس این فرایند انجام شده است. الگوریتم سیمپلکس با فضای نرم افزار تحلیلی انسیس ترکیب شده و سپس به اجرا درآمده و نتایج نهایی ارائه شده است.
    کلیدواژگان: بهینه سازی، سیمپلکس، دیسک دوار، دیسک غیرهمگن، المان محدود
  • محسن لوح موسوی، محمد بخشی جویباری، کن ایچیرو موری، محمود فرزین، سید جمال حسینی پور صفحه 121
    دراین تحقیق، فرایند هیدروفرمینگ لوله با فشار داخلی نوسانی در قالب جعبه ای شکل، به کمک روش اجزای محدود و به صورت سه بعدی شبیه سازی شده و سازوکار بهبود پرشدگی گوشه قالب، تحلیل و بررسی شده است. همچنین جوابهای حاصل با نتایج آزمایشگاهی مقایسه و درستی نتایج حاصل از روش اجزای محدود نشان داده شده است. به منظور افرایش بهبود میزان پرشدگی گوشه قالب، بر اساس سازوکار به دست آمده برای بهبود پرشدگی گوشه با فشار نوسانی، مسیر فشار داخلی نوسانی جدیدی پیشنهاد شده و به کمک روش اجزای محدود و در آزمایش ها، نشان داده شده است که درصد پرشدگی گوشه قالب با استفاده از مسیر فشار نوسانی جدید افزایش می یابد.
    کلیدواژگان: هیدروفرمینگ لوله، فشار نوسانی، شبیه سازی اجزای محدود، بهبود پرشدگی گوشه قالب
  • محمدحسن کیهانی، محمود شریعتی، محمود نوروزی صفحه 135
    در این مقاله یک حل تحلیلی برای انتقال حرارت هدایتی در استوانه ساخته شده از مواد مرکب در شرایط پایدار ارائه شده است. حل دقیق ارائه شده، برای بررسی انتقال حرارت در مخازن و لوله های کامپوزیتی بسیار مفید است. در این تحقیق تانسور ضرایب هدایت حرارتی برای مواد مرکب معرفی شده و نحوه تعیین ضرایب از روی خواص الیاف و ماده زمینه بیان شده است. در ادامه، معادله انتقال حرارت در دستگاه مختصات استوانه ای برای مواد کامپوزیتی - در شرایطی که الیاف در هر لمینا به دور استوانه پیچیده شده – به دست آمده و به روش جداسازی متغیرها حل دقیقی برای این معادله در شرایط مرزی معینی ارائه شده است.
    کلیدواژگان: حل تحلیلی، مواد مرکب، انتقال حرارت هدایتی، استوانه
  • یوسف حجت، محمدمراد شیخی، حسین موسوی هندری، رامین علی محمدی صفحه 153
    یاتاقان های مغناطیسی با توجه به ویژگی منحصر به فرد، در سال های اخیر بسیار مورد توجه محققان قرار گرفته اند. با توجه به نو بودن این زمینه تحقیقاتی در ایران، هدف از این تحقیق تدوین فناوری بوده و در اینجا مراحل طراحی، تحلیل و ساخت سیستم تعلیق مغناطیسی فعال ارائه می شود. فناوری به کار گرفته شده در این سیستم در واقع به عنوان پیشنیاز و به منظور توسعه آن برای دستیابی به دانش ساخت یاتاقان مغناطیسی، پیاده سازی شده است.
    کلیدواژگان: یاتاقان مغناطیسی، تعلیق مغناطیسی، رتور، معادله حالت
  • صفحه 163
|
  • Mehdi Maerefat, Mostafa Khosravi- Elhossaini Page 1
    Radiative heat transfer must be considered in retail refrigerators with glass doors. Some methods have been proposed for reducing radiative losses, like usage of double glased windows filled with argon or other types of transparent material with low emissivity in infrared band. For evaluation of thermal radiation in commercial refrigerator compared to infiltration loss, thermal conduction and facilities loss, a three dimensional model has been developed. In this model all wall surfaces are isothermal and evaporator with specific temperature located in roof. The radiative properties of glass are considered as actual. The results show that decreasing internal temperature of cabinet incentive radiation losses. These losses are almost independent of window surface temperature. Increasing of emissivity factor of evaporator, causes increasing of thermal radiation flux of evaporator which can be used in design improvement. Radiation flux of each surface have been compared with convection flux. This comparison show the importance of covering windows in unutilized times.
  • Majid Ali. Tavoli, Abalfazl Darvizeh, Ali Asghar Pashaee, Rahman Y. Moghaddam Page 15
    In this paper a new approach for forming sheet metals by explosion of gas mixtures is presented. As the sheet metal shapes by the impact and pressure resulted from the explosion, it undergoes through a plastic deformation phase. Testing apparatus which is built for the first time in Iran, consists of a thick-walled cylinder (expolsion chamber), various dies for shaping, and measuring instruments. Unlike techniques used in conventional systems, in this method, the wave impact acts as the male part of the die to form and produce different engineering components. Experimental results presented show the effect of various parameters such as thickness, boundary conditions, and the material type of the work-piece, also the percentage of gas mixture on the distribution of thickness/circumferential strain in the work-piece. Furthermore, an analytical model based on the plastic work calculations for the sheet metal deformation is presented.
  • Mehran Mahboubkhah, Mohammad Javad. Nategh, Siamak. E. Khadem Page 29
    Considering frictional, inertial and machining forces, the authors have presented an enhanced analysis of a hexapod table as used in milling machines. The Newton-Euler analysis of hexapod’s components has been implemented by a simulation program developed by the authors in MATLAB environment and the results have been verified by those of others. The impact of various loads involved in machining operation carried out on a milling machine equipped with hexapod table has been presented in the paper. This provides a potential machine tool designer with guidelines on the importance of these loads and helps him give appropriate weights to them.
  • Mehdi Maerefat, Amir Omidvar Page 39
    In cold season, draught or undesired local cooling sensation in ankle and neck region is one of the most frequent cases of complaint of the occupants. A person who are subjected to draughts in winter, tend to elevate the room temperature to counteract the cooling sensation, thereby increasing the energy consumption. In naturally ventilated buildings, draught is due to windows and other cold surfaces in the room. Draught is dependent on the air speed and on the magnitude of turbulence intensity. Serious draught complaints can often occur at mean speeds lower than those recommended by standards when turbulence intensity is high. So investigation of undesired local cooling in floor heating systems is very important, although in these systems the mean air speed is not significant. In this paper, the effects of size of window on draught are investigated in floor heating systems. Results demonstrated that, undesired thermal discomfort caused by local cooling phenomenon in floor heating systems is negligible. At the end, the probability of occurrence of local cooling phenomenon in floor heating systems is compared to vertical heating panels. Thereby the floor heating systems are more effective than the vertical heating panels in aspect of thermal comfort and energy consumption.
  • Reza Karimi, Majid. Mirzaei Page 51

    In cold season, draught or undesired local cooling sensation in ankle and neck region is one of the most frequent cases of complaint of the occupants. A person who are subjected to draughts in winter, tend to elevate the room temperature to counteract the cooling sensation, thereby increasing the energy consumption. In naturally ventilated buildings, draught is due to windows and other cold surfaces in the room. Draught is dependent on the air speed and on the magnitude of turbulence intensity. Serious draught complaints can often occur at mean speeds lower than those recommended by standards when turbulence intensity is high. So investigation of undesired local cooling in floor heating systems is very important, although in these systems the mean air speed is not significant. In this paper, the effects of size of window on draught are investigated in floor heating systems. Results demonstrated that, undesired thermal discomfort caused by local cooling phenomenon in floor heating systems is negligible. At the end, the probability of occurrence of local cooling phenomenon in floor heating systems is compared to vertical heating panels. Thereby the floor heating systems are more effective than the vertical heating panels in aspect of thermal comfort and energy consumption.

  • Gholam. Hossain. Liaghat, Habib-Ala. Sorailo Page 73
    honeycomb panel consists of an array of open hexagonal cells which their walls are perpendicular to face sheets although other panel sandwiches don’t have these perpendicular walls. Their design is often performed based on minimum weight. This research is aimed at minimizations of weight by means of computing honeycomb core girth. Weight optimization is done by means of Naive and numerical procedures. Numerical optimization is done by the sequential quadratic programming (SQP) method. Geometric parameters and optimized weight are calculated for hexagonal and square cells. Optimized weights for these two cross-sections are compared.
  • Parviz Rahnama, Amir. Abdollah Zadeh, Mohammad. Amar. Mofid Page 83
    In this study, in addition to forming a steel tube of D6AC by direct flowforming, in order to examine the effects of different parameters of heat treatment process on the a for mentioned part properties, different cycles of heat treatment process are designed and after doing so, mechanical properties and microstructural changes of flowformed tube are investigated. For this purpose, at 850, 900 and 950 ˚C austenitizing temperatures for 15 and 30 minutes and AUS-BAY quenching at 510 ˚C for 10 minutes, and then quenching at 60 ˚C oil are used. Initial tempering for 2 hours at 250 ˚C and final tempering for 2 hours at 250, 300, 350 and 450 ˚C was performed. Investigations show that the optimum heat treatment cycle is austenitizing at 850 ˚C for 30 minutes, and final tempering at 300 ˚C, because of creating high strength and suitability for fracture toughness. Due to small grains of initial austenite, the ductility properties are also adequate.
  • Behzad Ghadiri, Mani. Razi, Sabah Hamidi Page 93
    In this paper linear aeroelastic analysis of a swept wing with two degrees of freedom in an incompressible flow is investigated in time - domain. The equations of the motion of an elastic wing are derived from Lagrange’s equations in time - domain. The wing is modeled as a cantilever beam rigidly connected to the root. Considering assumed modes of cantilever beam, aerodynamic forces and moments acting on the wing are derived using strip - theory in an unsteady incompressible potential fluid flow. The governing aeroelastic equations of the system have been introduced in dimensionless form. These equations are solved via a numerical method. Comparisons between obtained results and both available experimental data and the results of some cited references indicate a close agreement.
  • Behrooz Farshi, Mohammad. Hossein. Faezi Page 107
    There are numerous applications for gas turbine discs in the aerospace industries such as in turbojet engines. These discs normally work under high temperature while subjected to high angular velocities. Minimizing the weight of such items in aerospace applications results in benefits such as low dead weights and lower costs. Optimization of rotating discs is historically, an area of research due to their vast utilization in industry. The gas turbine disc is one of examples to name. Gas turbine discs work mostly at high temperature gradients and are subjected to high angular velocities. High speed results in large centrifugal forces in disc and simultaneous high temperatures reduces the disc material strength, thus the later increases stress in disc automatically. In order to obtain a reliable disc analysis and arrive at the corresponding correct stress distribution, solution should consider changes in material properties due to the temperature field throughout the disc. To this end, an inhomogeneous disc model with variable thickness is considered. Using the variable material properties method, stresses are obtained for the disc under rotation and a steady temperature field. In this paper this is done by modeling the rotating disc as a series of different rings with constant properties. The optimum disc profile is arrived at by sequentially proportioning the thickness of each ring to satisfy stress requirements. In this paper these are done using the simplex method. Simplex algorithm is applied in Ansys software and the results are presented.
  • Mohsen. Loh. Mousavi_M. Bakhshi. Jooybari_Kan . E. Mori_Mahmood. Farzin_. Javad. Hosseinipour Page 121
    In this study, pulsating hydroforming of tube in a box die is simulated using the three dimensional finite element method to investigate the mechanism of improvement of the corner filling. In addition, the results obtained from the simulation are compared with experimental observations, and the validity of the simulation results is verified. Based on a better understanding of the mechanism of improvement of the corner filling, a new pulsating pressure path is proposed to increase the corner filling. It has been shown that the proposed pulsating pressure path is more effective in increasing the corner filling of the box shape tube hydroforming process.
  • Mohammad. Hasan. Kayhani, Mahmood. Shariati, Mahmood. Norouzi Page 135
    This paper presents an analytical solution for steady state conductive heat transfer in a cylindrical composite laminate. The results of this solution can be pretty useful in investigating heat transfer in pipes and reservoirs. In this research, tensor of thermal conductivity coefficients for composite materials is presented and the procedure of determination of the coefficients is described based on the properties of fibers and matrix material. Then, the equation of heat transfer of composite materials has been determined in cylindrical coordinates. The research has been done for conditions that fibers are wound around the cylinder and the heat transfer equation has been solved via separation of variables method.
  • Yusef. Hojjat_Mohammad. Morad. Sheikhi_Hosein . Mosavi. Hondori_Ramin. Alimohamadi Page 153
    In recent years many researches have been focused on active magnetic bearing (AMB) systems. AMB offers advantages such as, contact less and friction free operation, excellent performance over a wide range of temperature, no need for lubricant and longer life. Technology of magnetic bearings can be considered as a new field of research in Iran. This paper presents design, manufacturing and control of a magnetically levitation system with successful operation. This research concluded with documentation of the AMB technology which is prerequisite for earning the technology of active magnetic systems (AMS) and paves the way to develop it.