فهرست مطالب
مجله مهندسی مکانیک شریف
سال سی و سوم شماره 1 (بهار و تابستان 1396)
- تاریخ انتشار: 1396/04/31
- تعداد عناوین: 14
-
- مقاله پژوهشی
-
صفحات 3-15در سیستم های دوار با پایه ی کشسان، نامیزانی سیستم باعث ارتعاشات پایه می شود. این ارتعاشات نیز موجب اعمال یک گشتاور نوسانی به روتور و نوسانی شدن سرعت دوران می شود. بنابراین یک سازوکار انعکاسی شکل می گیرد که می تواند رفتاری غیرخطی با طیف متفاوتی
از پاسخ ها را به نمایش بگذارد. در مجاورت بسامد طبیعی، ارتعاشات بزرگ پایه موجب افزایش چشمگیر توان مصرفی می شود و از افزایش سرعت روتور جلوگیری می کند. در این حالت ممکن است سیستم توان کافی برای گذر از تشدید را نداشته و دچار قفل شدگی تشدید شود. در این نوشتار پیشنهاد شده است به منظور ایجاد اغتشاش در شکل گیری سازوکار قفل شدگی، یک نامیزانی آزاد به سیستم اضافه شود. برای بررسی کارایی این روش، معادلات دینامیکی سیستم استخراج شده و به روش هارمونیک بالانس و روش عددی حل شده است. نتایج به دست آمده نشان می دهد با افزودن یک نامیزانی آزاد، می توان محدوده ی قفل شدگی و امکان گذر از آن را بهبود داد.کلیدواژگان: نامیزانی دوار، قفل شدگی تشدید، دیسک الحاقی نامیزان -
صفحات 17-28محفظه یکی از اجزای اصلی کمپرسور جریان شعاعی است و نقش آن جمع آوری و تحویل جریان به تجهیزات پس از کمپرسور است. طراحی محفظه، بر نسبت فشار، بازده و محدوده ی عملکرد پایدار کمپرسور تاثیر مستقیم و قابل توجهی دارد. محفظه می تواند باعث ایجاد ناهمگونی فشار در اجزای بالادست خود شود که منجر به ایجاد یک نیروی خالص بر محور پروانه می شود. در پژوهش حاضر، براساس شناسایی اصول طراحی و پارامترهای موثر بر عملکرد محفظه، یک روش طراحی بهینه ارائه می شود. سپس با استفاده از ابزار دینامیک سیالات محاسباتی، مقادیر بهینه ی پارامترها که منجر به افزایش نسبت فشار سکون، افرایش بازیابی فشار استاتیک، کاهش افت فشار سکون و نیز کاهش نیروی خالص شعاعی در محفظه می شوند، شناسایی خواهد شد. مدل های مختلف در نقطه ی طراحی و نقاط خارج طرح ارزیابی و طرح بهینه با اضافه کردن ملاحظات مربوط به زبانه و مخروط خروجی ساخته می شود و روی بستر آزمون نصب و نتایج عملکردی آن استخراج خواهد شد. نتایج نشان می دهد، در نقطه ی طراحی حدود 40 درصد تغییر در مساحت خروجی، منجر به 14 درصد تغییر در ضریب بازیابی فشار، و 18 درصد تغییر در افت فشار می شود؛ در حالی که نیروی محوری را تا دو برابر تغییر می دهد. نتایج آزمون کمپرسور با محفظه ی جدید که در
اعتبارسنجی نتایج عددی کاربرد دارد، نشان می دهد که در سرعت دورانی 70 هزار دوربردقیقه، 2٫5 درصد نسبت فشار و 1٫9 درصد بازده آیزنتروپیک کمپرسور افزایش یافته است که بهبود حائز اهمیتی است.کلیدواژگان: کمپرسور جریان شعاعی، محفظه، نسبت فشار، بازده آیزنتروپیک، گردابه ی آزاد، فشار غیریکنواخت پیرامونی -
صفحات 29-36خواص منحصر به فرد الکتریکی و مکانیکی نانوسازه های کربنی آنها را در زمره موادی قرار داده که کاربردهای متنوعی دارند، و این مهم مطالعه ی رفتار مکانیکی آنها را حائز اهمیت گردانده است. در این پژوهش با استفاده از نظریه ی آیفانتیس و تنش کوپل بهبود یافته بهبودیافته به پیش بینی رفتار ارتعاشی نانوصفحات گرافن با شرایط مرزی ساده پرداخته شده است. نتایج نشان می دهد که نظریه ی آیفانتیس را می توان به عنوان نظریه یی با یک مقیاس طول برای این مهم استفاده کرد در حالی که نظریه ی تنش کوپل شاید چندان مناسب نباشد. همچنین دیده می شود که پارامتر مقیاس طول نه تنها تابعی از کایرالیتی و سایز نانوصفحات مربعی است بلکه با تغییر نظریه ی غیرکلاسیک نیز تغییر می کند. شایان ذکر است که نظریه های گرادیان الاستیسیته مقیاس شده ضرورتا در تقریب بسامدهای مرتبه بالاتر باهم تطابق ندارند هرچند که اختلاف آنها با افزایش طول ورق مربعی کاهش می یابد.کلیدواژگان: ارتعاش آزاد صفحات گرافن، کایرالیتی، نظریه ی آیفانتیس، نظریه ی تنش کوپل بهبودیافته
-
صفحات 37-47شکست خستگی معمولا در فاق موجود در سطح ماده ٓجایی که به علت تمرکز تنش، مقدار تنش افزایش یافته استٓ رخ می دهد. نظریه های مختلفی برای پیش بینی شکست خستگی نمونه های فلزی فاق دار ارائه شده است. این نوشتار به ارزیابی نظریه های مختلف پیش بینی شکست خستگی نمونه های فاق دار فولادی براساس قابلیت پیش بینی آنها می پردازد. آزمایش های تجربی کششی ساده و خستگی از نوع خمش چرخان روی نمونه های استوانه یی ساده و فاق دار فولاد 45C K انجام شده و مشخصات مکانیکی و هم چنین نمودار تنشٓ عمر نمونه ی ساده و نمونه های فاق دار به دست آمده اند. نظریه های بیشینه تنش، نیوبر، پترسون، تغییرات تنش، فاصله ی بحرانی و ضعیف ترین اتصال برای پیش بینی ضریب کاهش استحکام خستگی نمونه های فاق دار فولاد 45C K استفاده شده اند و نتایج این نظریه ها با نتایج آزمایش مقایسه شده است. مقایسه ی نتایج نظری و آزمایشگاهی نشان داده که نظریه ی ضعیف ترین اتصال نسبت به نظریه های کلاسیک از دقت بهتری برخوردار است.کلیدواژگان: فاق، عمر خستگی، شکست خستگی، فولاد CK45
-
صفحات 49-54در این نوشتار الیاف شیشه تقویت شده با سیال سخت شونده ی برشی، و سخت شونده ی برشی به همراه نانوذرات خاک رس تحت آزمون شبه استاتیکی بررسی شده است. یکی از مزیت های سیال ضخیم شونده ی برشی غلظت بالای آن است. برای تهیه ی سیال سخت شونده ی پلی اتیلن گلیکول به صورت سیال پایه و نانوذرات سیلیکا به آرامی به سیال اضافه می شود. آزمون شبه استاتیکی برای هرسه حالت پارچه شیشه خشک سیال سخت شونده ی برشی و پارچه شیشهٓ سیال سخت شونده ی برشیٓ نانوذرات خاک رس روی سطح مشخص انجام شده است. آزمون شبه استاتیکی برای هر سه حالت پارچه های آغشته نشده، پارچه های آغشته شده به سیال سخت شونده ی برشی، و پارچه های آغشته شده به سیال سخت شونده ی برشی به همراه نانو ذرات خاک رس انجام شد. نتایج مطالعات به وضوح نشان گر افزایش قابل توجه مقاومت نفوذی پارچه های شیشه یی آغشته شده به سیال سخت شونده ی برشی به همراه نانو ذرات خاک رس است.کلیدواژگان: سیال سخت شونده ی برشی، رئولوژی، الیاف شیشه، نانوذرات سیلیکا، نانوذرات خاک رس
-
صفحات 55-61درباره ی اثربخشی روش های نوین یادگیری بلندمدت لغات انگلیسی تاکنون بررسی چندانی صورت نگرفته است. پژوهش حاضر با هدف بررسی مقایسه یی آموزش 330 لغت در فهرست لغات آکادمیک C o x h e a d )2000(، با استفاده از رایانه، تلفن همراه و فرهنگ لغت در حوزه ی یادگیری بلندمدت زبان آموزان در ایران، انجام شده است. در این راستا پس از برگزاری آزمون تعیین سطح آکسفورد به عنوان آزمون مهارت، 264 زبان آموز در رشته های علوم پایه و فنی و مهندسی انتخاب و به سه گروه آزمایشی و یک گروه کنترل تقسیم شدند. طبق نتایج این مطالعه، زبان آموزانی که به طور آنلاین و از طریق رایانه آموزش دیده بودند توانایی بیشتری در به خاطرسپردن لغات در درازمدت از خود نشان دادند. نتایج این تحقیق روش های نوین آموزشی با استفاده از رایانه در یادگیری بلندمدت لغات انگلیسی را توصیه می کند.کلیدواژگان: یادگیری با استفاده از رایانه، یادگیری با استفاده از تلفن همراه، یادگیری با استفاده از فرهنگ لغت، یادگیری لغات انگلیسی
-
صفحات 63-71در این نوشتار خصوصیات رفتار ارتعاشی میکروروتورهای نامیزان ساخته شده از مواد هدفمند تابعی براساس نظریه ی غیرکلاسیک تنش کوپلی به طور تحلیلی مورد بررسی قرار گرفته است. این نظریه قادر به پوشش اثرات ناشی از کوچکی ابعاد هندسی سازه ها و قطعات است. ابتدا معادلات کوپل حاکم بر نوسانات عرضی مجموعه میکروروتور استخراج شده و با به کاربردن روش گلرکین و در نظر گرفتن دو مود اول خمشی، عباراتی برای دو بسامد اول طبیعی در هریک از حالات لنگ زنی هم جهت و خلاف جهت با دوران شفت ارائه شده است. به علاوه، رابطه یی برای دامنه ی ارتعاشات پایدار مجموعه نامیزان استخراج شده است. اثرات خصوصیات مادی غیرکلاسیک بر بسامدهای طبیعی و دامنه ی ارتعاشات با استفاده از این نتایج تحلیلی قابل بررسی است. نتایجی عددی نیز در مثال های خاصی ارائه شده است تا تاثیرات قابل توجه خصوصیات مادی غیرکلاسیک به صورت عددی مشخص شود.کلیدواژگان: میکروروتور، مواد هدفمند تابعی، نظریه ی تنش کوپلی، ارتعاشات آزاد و اجباری، نامیزانی
-
صفحات 73-82در این نوشتار عملکرد ارتعاشی یک میراگر غیرخطی وابسته به مکان و سرعت مورد بررسی قرار می گیرد. میراگر پیشنهادی با اعمال تغییرات مناسب در ساختار یک میراگر خطی به گونه یی است که دارای ضریب میرایی متغیری وابسته به جابه جایی و سرعت پیستون است. همچنین تاثیر تغییرات اندازه حرکت سیال در روزنه ی پیستون بر عملکرد ارتعاشی سیستم با مطالعات پیشین مقایسه شده است. پروفیل های جابه جایی، سرعت، نیروی میرایی و نیروی منتقل شده به پایه ی سیستم برای یک سیستم جرمٓ فنر مجهز به میراگر غیرخطی وابسته به مکان و سرعت به دست آمده است. نتایج به دست آمده با نتایج ارائه شده در مطالعات قبلی برای سیستم مجهز به میراگر خطی و همچنین میراگر غیرخطی فقط وابسته به مکان مقایسه شده است. پاسخ های شبیه سازی موید عملکرد بسیار بهتر میراگر غیرخطی وابسته به مکان و سرعت در کاهش ارتعاشات سیستم در مقایسه با سایر میراگرهای معرفی شده است.کلیدواژگان: ارتعاشات آزاد، ارتعاشات اجباری، ارتعاشات تشدید، میراگر غیرخطی وابسته به مکان و سرعت، قانون بقای اندازه حرکت
-
صفحات 83-91یافتن الگوی صحیح جریان سیال در پمپ های دیافراگمی، توزیع نیروی حاصل از فشار اعمالی از سوی سیال بر دیافراگم و همچنین یافتن شرایط مناسب عملکرد برای طراحی به دور از حالت های ناپایداری چون کاویتاسیون، یکی از اهداف این مطالعه است. هدف این تحقیق یافتن روشی مناسب برای شبیه سازی عملکرد این نوع از پمپ ها در مقابل روش های پیچیده تحلیلی و هزینه بر آزمایشگاهی است. یک نمونه پمپ دیافراگمی متداول در ایستگاه تقلیل فشار گاز شهری مورد بررسی قرار گرفته، بر اساس اطلاعات فنی استخراج شده از این پمپ، مدلی برای شبیه سازی آن با نرم افزار انسیس سی اف ایکس پیشنهاد شده است. نرخ جریان سیال مرکاپتان با توجه به اطلاعات فنی پمپ در ایستگاه دریافت و نتایج مدل سازی با آن مقایسه شده است. برخی از نتایجی که در این مقاله به آن اشاره شده است عبارتند از میدان های سرعت و فشار برای سیال ورودی و خروجی، نرخ جریان سیال برحسب جابه جایی دیافراگم، حجم سیال ورودی و خروجی برحسب زمان و همچنین نرخ جریان سیال خروجی برحسب فرکانس حرکتی دیافراگم که نتایج موجود در بیشترین حالت دارای خطایی کمتر از 10 درصد می باشند.کلیدواژگان: پمپ دیافراگمی، برهمکنش سازه و سیال، نرم افزار A N S Y S C F X
-
صفحات 93-99حل عددی معادلات دیفرانسیل با استفاده از بسترهای C P U و G P U مبتنی بر پیاده سازی نرم افزاری است. در سال های اخیر، راهکار جدیدی مبتنی بر پیاده سازی سخت افزاری معادلات با استفاده از بستر F P G A، به دلیل افزایش سرعت حل و کاهش توان مصرفی، مورد توجه جدی قرار گرفته است. در این پژوهش با حل چند مسئله ی نوعی، شامل سیستم جرم و فنر و معادله ی موج، روش پیاده سازی سخت افزاری برای حل معادلات دیفرانسیل بر روی F P G A، مزایا و چالش های این پیاده سازی و روش های حل آن ارائه شده است. نتایج سرعت پردازش برای حل سیستم تک جرم و فنر نشان می دهد که سرعت C P U تقریبا برابر F P G A است ولی برای سیستم 6 جرم و فنر سرعت F P G A 8 برابر C P U است. همچنین نتایج سرعت پردازش حل معادله ی موج نشان دهنده ی افزایش 3٫6 برابری سرعت F P G A نسبت به C P U است. این نتایج نشان گر افزایش کارایی F P G A با افزایش تعداد المان های محاسباتی است.کلیدواژگان: محاسبات قابل بازپیکربندی، افزایش سرعت حل، معادلات دیفرانسیل عادی و پاره یی
- مروری
-
صفحات 101-120طراحی خستگی اجزاء بالگرد کاری سخت و چالش برانگیز است. هدف از ارزیابی خستگی بالگرد نشان دادن این نکته است که در طول عمر کاری بالگرد، انتظار واماندگی فاجعه آفرین ناشی از خستگی کاملا از بین رفته و نیز وقوع ترک خوردگی غیرفاجعه آمیز به حد کافی در سطح پایینی باقی می ماند، طوری که استفاده ی اقتصادی از سازه بالگرد حاصل شود. روش طراحی خستگی که اغلب توسط جامعه ی بالگردسازی اعمال شده، براساس فلسفه ی «عمر مطمئن» بوده است. در سال های بعد، به علت کارآمد نبودن روش عمر مطمئن لزوم استفاده از روش های دیگر تحلیل عمر خستگی ٓمانند روش تحمل نقص و روش تحمل آسیبٓ بیشتر احساس شد. در این مقاله ضمن مرور روش های مختلف طراحی خستگی بالگرد، مزایا و معایب هر روش ارائه می شود. در پایان جنبه های دیگر طراحی خستگی بالگرد مورد بررسی قرار می گیرد.کلیدواژگان: خستگی بالگرد، عمر خستگی، طراحی خستگی بالگرد، روش های خستگی بالگرد
- یادداشت فنی
-
صفحات 121-127در این پژوهش یک سیستم کنترل فازی چندگانه به منظور برنامه ریزی حرکت یک ربات افزوده در یک محیط دوبعدی با حضور موانع طراحی شده است. سیستم کنترل به گونه یی است که مستقل از تعداد درجات آزادی سیستم است. با افزودن هر تعداد عضو به بازو تغییری در کنترل گرهای فازی، توابع عضویت و تعداد سیگنال های ورودی و خروجی به وجود نمی آید. در طراحی کنترل گرهای فازی چند رفتار مختلف در مواجهه با خطرات و همچنین نزدیک شدن به هدف با هم آمیخته شده است. با استفاده از این روش ربات افزوده با سه و شش درجه آزادی همزمان با رسیدن به هدف از برخورد با مانع اجتناب می کند. استفاده از منطق فازی و تدوین قوانین ساده با استفاده از چند کنترل گر فازی مختلف و ترکیب خروجی آن ها امکان گسترش رفتار بازوی مکانیکی را تسهیل کرده و قابلیت گسترش و بهینه سازی رفتارها را نیز محفوظ داشته است.کلیدواژگان: برنامه ریزی حرکت، ربات افزوده، کنترل فازی، محیط نامعین
-
صفحات 129-136نوشتار حاضر به مدل سازی ترمودینامیکی یک نیروگاه توربین گازی با توان تولیدی M W 30 و (k g/s) 14 بخار اشباع در فشار b a r 20 پرداخته است. این سیستم معروف به مسئله C G A M است. در مسئله ی C G A M تابع هدف شامل مجموع هزینه ی سرمایه گذاری و همچنین هزینه ی سوخت مصرفی است. در این نوشتار بهینه سازی با کمینه سازی تابع هدف و نیز به کارگیری الگوریتم ژنتیک و الگوریتم اجتماع ذرات به کمک نرم افزار متلب انجام می شود و در نهایت عملکرد این دو الگوریتم با یکدیگر مقایسه می شود. نتایج حاصل از مقایسه ی تعداد توابع ارزیابی شده (N F E) این دو الگوریتم نشان می دهد که سرعت همگرایی الگوریتم اجتماع ذرات در یافتن کمترین تابع هزینه نسبت به الگوریتم ژنتیک بالاتر است. همچنین در حل مسئله ی C G A M الگوریتم بهینه سازی اجتماع ذرات به لحاظ پیاده سازی، انعطاف پذیری، و سهولت برنامه نویسی به مراتب از الگوریتم ژنتیک تواناتر است.کلیدواژگان: بهینه سازی، C G A M، الگوریتم ژنتیک، الگوریتم اجتماع ذرات
-
صفحات 137-145پلیمرهای حافظه دار دسته یی از مواد هوشمندند که نسبت به تحریک حرارتی عکس العمل نشان می دهند. این مواد پس از تغییر شکل، طی یک سری چرخه های ترمودینامیکی، شکل اولیه ی خود را بازیابی می کنند. استحکام کم این مواد کاربردهای آن را محدود می کند. یکی از راه های رفع این محدودیت، طراحی نانوکامپوزیت هایی بر پایه ی پلیمر حافظه دار است. در این مطالعه اثرات ناشی از افزودن نانوصفحات گرافن بر عملکرد این مواد بررسی می شود. در این راستا، از یک مدل ویسکوالاستیک برای توصیف رفتار ماده استفاده می شود. برای مدل سازی نانوکامپوزیت و بررسی اثرات درصد حجمی و نسبت منظری نانوذرات از روش اجزاء محدود استفاده شده است. بدین منظور، دو چرخه ترمودینامیکی طراحی شده و نتایج در نمودارهای تنشٓ کرنشٓ دما ارائه می شود. با افزایش درصد حجمی و نسبت منظری نانوذرات، مقدار تنش و مقدار تنش بازیابی شده افزایش می یابد. با افزودن تا 3\٪ نانوذره و اعمال کرنش تا 20\٪ اختلالی نیز بر روی عملکرد نانوکامپوزیت ایجاد نمی کند.کلیدواژگان: نانوکامپوزیت پایه پلیمر حافظه دار، مدل ویسکوالاستیک، روش اجزاء محدود، نانوصفحات گرافن
-
Pages 3-15Vibration problems in rotating machines can be extremely frustrating and may lead to great damages, reduced reliability, and unpleasant side-effects. Unbalanced rotating masses are a main source of machine vibrations. In an unbalanced rotating system with elastic supports, mass center displacements induce an oscillatory force into the support and cause base vibrations. On the other hand, base vibrations introduce an oscillatory torque to the rotor and cause velocity oscillations. In this way, a reciprocal action forms a complex set of nonlinear equations which depend on actuating torque, giving a wide range of harmonic, periodic and chaotic solutions. Close to the system natural frequency, base's high amplitude vibrations result in considerable power waste and prevent rotor acceleration. In such a case, system may suffer power shortage and remain in resonance. This phenomenon is named resonant capture.In this article, it is proposed to interrupt capture mechanism by adding a free unbalanced mass to the system. It is predicted that system base vibrations force the added mass to rotate or vibrate, and the reacting forces will affect the base motions. This may delay the capture mechanism and provide enough time for the system to accelerate and escape the capture region.To evaluate the efficiency of the proposed method, an unbalanced rotating system with elastic supports is considered. The nonlinear governing equations of motion are derived and using harmonic balance method, capture region is defined. Numerical results are provided to assess the validity of obtained solutions. Then a free rotating unbalanced disk is added to the system. Using harmonic balance method and numerical solutions, effect of the added free unbalanced disk on the capture range is discussed. Numerical results are provided for different unbalanced added discs and different initial conditions. Obtained results show that the added unbalanced mass can improve the system capability to narrow the capture region and escape it.Keywords: U?n?b?a?l?a?n?c?e?d r?o?t?o?r, r?e?s?o?n?a?n?t c?a?p?t?u?r?e, a?d?d?e?d u?n?b?a?l?a?n?c?e?d d?i?s?k
-
Pages 17-28Volute is one of the main components in radial flow compressors where the working fluid is collected and delivered to the compressor downstream pipelines. Volute design has direct and strong effects on the compressor performance and its stable operating range. This component causes distorted pressure fields in upstream flow passages which can lead to mechanical forces on the impeller. In the current research, based on the fundamental concepts of volute design, a new approach for volute design is considered and the effective parameters on volute performance are recognized. Using computational fluid dynamic (CFD) tools, the optimum values of effective parameters which lead to an increase in volute pressure ratio and static pressure recovery coefficient as well as decreasing the total pressure loss coefficient and the net radial force are explored.Considering the exit cone and the tongue area geometry design criteria, the models are numerically evaluated at the design point and off-design conditions to select the optimum model for fabrication and testing. The new volute is installed at a compressor test rig and the compressor characteristic curves are obtained. At the design point, area variation by 40% results in 14% variation in static pressure recovery factor and 18% variation in total pressure loss coefficient, however, it leads to increase the net radial force on impeller up to 100%. Experimental results, which are used for numerical model verification, show that the compressor pressure ratio and the isentropic efficiency are increased by 2.5% and 1.9% at 70,000rpm respectively.Keywords: Radial flow compressor, volute, tongue area, static pressure recovery, isentropic efficiency, free vortex, non-uniform circumferential pressure
-
Pages 29-36The unique electrical and mechanical properties of carbon nano-structures make them desired materials with a wide range of applicability. Hence, the study of their mechanical behavior is an important topic which has attracted a great deal of attention. Graphene, a two-dimensional carbon nano-structures with an one-atom thickness, exhibits so wonderful electrical, mechanical, thermal and optical properties which make it suitable to use in micro-/nano-electromechanical system such as nano-scale electromechanical resonators, vibrational behavior of which affects their functionality.The importance of incorporating the size effect on continuum mechanics to simulate the mechanical behavior of nano-structures is well-known. To this end, different higher-order continuum mechanics that contain additional material constants have been developed. However, the recognition of an efficient non-classical theory with respect to nano-materials is a challenging process. Modified couple stress theory, Eringen's nonlocal elasticity, and Aifantis's theory are some of non-classical theories used because of existence one material length scale. Although Eringen's nonlocal elasticity is the popular theory to simulate mechanical behavior of carbon nano-structures, its microstructure-dependent constitutive model does not allow the construction of the energy functional. Hence, this article is aimed at investigating the utilization of modified couple stress theory and Aifantis's theory to estimate natural frequencies of simply-supported single-layered graphene sheets. For this purpose, it is tried to estimate material length scale of theories by point-by-point matching between available first natural frequency of graphene sheets determined by molecular dynamic method and the obtained data. According to the results, modified couple stress theory cannot be used unless one substitutes square of length scale parameter with a minus value in stain energy equation or adds the gradient velocity to the kinetic energy equation by a new material length scale. The former leads to a non-positive definite strain energy function, and the later makes a gradient elasticity theory with two material length scales. Aifantis's theory is more applicable than modified couple stress theory in this situation. It is also seen that the higher order natural frequencies, estimated by different gradient elasticity theories and, material length scale of which is fixed by using molecular dynamic data, are different, although this difference decreases with an increase in side-length of square nano-plate. It can be concluded that chirality, side-length of nano-plate, and the used gradient elasticity theory affect the material length scales, as well.Keywords: F?r?e?e v?i?b?r?a?t?i?o?n o?f g?r?a?p?h?e?n?e s?h?e?e?t, c?h?i?r?a?l?i?t?y, a?i?f?a?n?t?i?s's t?h?e?o?r?y, c?o?u?p?l?e s?t?r?e?s?s t?h?e?o?r?y
-
Pages 37-47Typically, fatigue failure of a component happens at a notch where the stress level rises because of the stress concentration effect. Notch is usually defined as a geometric discontinuity. Notch may be introduced either by design or by the manufacturing process. A hole in a component is an example of a design notch. Material and fabrication defects, such as weld defects, inclusions, casting defects, or machining marks, are notches which are introduced due to the manufacturing process. A variety of methods are available to predict fatigue failure of notched specimens. The purpose of the present investigation is to rank such methods according to their predictive capability. Tensile tests were conducted on CK45 steel specimens and mechanical properties and stress-strain curve were obtained. Rotating bending fatigue tests were performed at room temperature on smooth and notched cylindrical specimens, and S-N curves were obtained. To better investigate the notch-size effect on fatigue life of the cylindrical specimens, two different notch geometries were used. Based on the obtained experimental S-N curve for smooth specimens, fatigue strength reduction factor or fatigue life for notched specimens were predicted by Neuber, Peterson, maximum stress, critical distance (Point method, Line method, Area method) and weakest-link (Area method, Volume method) theories and comparison of experimental results were considered. The predictions by maximum stress and stress gradient methods were conservative, which is some consolation to engineering designers; nevertheless, the errors were high. Neuber, Peterson and critical distance methods are based on stress gradient in notch root radius and predictions by these methods were not accurate. Also, Peterson, Neuber and Stress gradient methods are not consistent with finite element results. The predicted fatigue strength reduction factors by weakest-link methods were the closest to the experimental results. Finally, the weakest-link theory is recommended in terms of predictive capability, availability of the required materials data, and the compatibility with FEA stresses to predict fatigue strength factor among the studied methods in this research.Keywords: Notch, fatigue life, fatigue failure, CK45 steel
-
Pages 49-54Fluids can be divided into several classifications in terms of their viscosity behavior with relation to shear rate. One of these classes is the Newtonian u{fb02}uids, which exhibit a constant viscosity with the increase of shear rate. The main feature of Shear Thickening Fluid )STF( exhibits an increased viscosity with the increase of shear rate. The shear thickening phenomenon occurs in most of the concentrated colloidal suspensions containing hard solid particles in fluid. The behavior of continuous phase has a significant impact on the properties of the STF. Due to the appearance of OH bonds on the surface of silica particles and also the appearance of this type of bond in the polyethylene glycol, the formation of hydrogen bonds. In this paper, glass fiber reinforced shear thickening fluid and shear thickening fluid with clay nanoparticles under quasi-static tests is investigated. A shear thickening fluid was prepared successfully and rheological behavior was was investigated. One of the disadvantages of shear thickening fluid (STF) is high concentration. To prepare shear thickening fluid polyethylene glycol as a base fluid and the silica nanoparticles is added slowly to the fluid. After to create shear thickening fluid clay nano particles are added to the fluid. Glass fabrics were soaked in STF/ethanol (1:3) solution to prepare STF-glass fabric composite and STF- nanoclay-glass composite. For better immersion of fibers, at first STF is diluted in ethanol, and then the fibers are left there in for a specified period in order to impregnate all fibers with the fluid. The composite's sensitivity to the impact will be reduced through ethanol combining with the fluid and its elimination. After this stage, to eliminate the ethanol in the sample, it is heated at a temperature range of $60-{70^0}C$. Quasi-static resistant tests were carried out on three modes the neat glass fabrics and STF- glass fabric and STF-nanoclay glass fabrics composites. The current study clearly displays a significant enhancement in penetration resistance of glass fabric impregnated with STF-nanoclay.Keywords: S?h?e?a?r t?h?i?c?k?e?n?i?n?g f?l?u?i?d, r?h?e?o?l?o?g?i?c?a?l p?r?o?p?e?r?t?y, g?l?a?s?s f?a?b?r?i?c?s, n?a?n?o?s?i?l?i?c?a, n?a?n?o?c?l?a?y
-
Pages 55-61With the rapid development of ubiquitous learning, the emerging technologies contribute significantly to English language learning. An increasing number of studies began to discover the effects of computer and mobile language learning on the second language areas and skills. With each language area, the relevant technologies are embedded in the context of English pedagogy to facilitate the efficiency of learning. However, to date, it seems that no research has been conducted to examine the effectiveness of dynamic methods of English vocabulary learning. To shed light on the pre-existed pedagogical values of computer and mobile language learning for the second language vocabulary, the study pursued the purpose of investigating the effectiveness of diverse teaching methods of computer-assisted, mobile-based, and dictionary-use on student's long-term retention of 330 words of Coxhead's (2000) academic word list. To this end, 264 freshman university students were randomly distributed into four groups and received new academic words either on paper or through computer and SMS. After learning the words of each sublist, periodical tests were given from the proposed system for the learned vocabulary to test whether students have learned the new English vocabulary over time. The findings of the current research revealed that the regular distribution of the second language academic words via the flexible proposed learning modes led to better vocabulary retention over time. The findings indicated that the students recognized more vocabulary for the recall test, given one month after the end of the training period. However, the results suggested that those received online instruction via computer-supported learning recalled vocabulary better when compared to their counterparts. The usability and convenience of the flexible proposed technology-enhanced learning modes support an overall positive response from university students. To conclude, technologies in use for English vocabulary learning promote long-term retention of vocabulary. It is, therefore, suggested that teacher education and training in the area of technology in use for second language vocabulary learning requires further research.Keywords: M?o?b?i?l?e - l?e?a?r?n?i?n?g_c?o?m?p?u?t?e?r - l?e?a?r?n?i?n?g_d?i?c?t?i?o?n?a?r?y-b?a?s?e?d l?e?a?r?n?i?n?g_e?n?g?l?i?s?h v?o?c?a?b?u?l?a?r?y l?e?a?r?n?i?n?g
-
Pages 63-71In this paper, flexural vibration behavior of functionally graded micro-rotors with a mass eccentricity is investigated on the basis of the modified couple stress theory. The modified couple stress theory is a non-classical one which is capable to take into account the small-scale effects on micro-scale elements and structures with just one higher-order or non-classical material property.
It should be noted that it has been experimentally verified that the classical continuum theory fails to properly simulate the mechanical behavior of small-scale flexible structures. The micro-rotor is composed of a flexible shaft and a disk at its middle. Here, the disk is assumed to have a mass eccentricity, which causes forced vibrations. Additionally, the shaft of the micro-rotor is assumed to be made of a functionally graded (FG) material with varying properties in the radial direction. In derivation of the formulation, both gyroscopic effects and rotary inertia are included. By setting the non-classical material property to zero, the formulation is reduced to the classical continuum formulation. Governing equations of motion of the micro-rotor in lateral motions as well as the general form of boundary conditions are derived with the aid of the Hamilton's principle. These equations are transformed into a partial differential equation utilizing complex functions. Next, based on the Galerkin method with two-mode truncation, analytical expressions for vibration characteristics of the micro-rotor, including first two natural requencies in both forward and backward whirl motions, are obtained for the simply-supported cases. Moreover, the amplitude of the forced vibration of the micro-rotor in steady state condition is determined. The forced vibration is due to the mass eccentricity of the disk. With these analytical results in hand, it is an opportunity to evaluate the effect of non-classical material property on the vibrational characteristics of micro-rotors. These non-classical effects have been numerically investigated in an example provided.Keywords: M?i?c?r?o-r?o?t?o?r, f?u?n?c?t?i?o?n?a?l?l?y g?r?a?d?e?d m?a?t?e?r?i?a?l?s, c?o?u?p?l?e s?t?r?e?s?s t?h?e?o?r?y, f?r?e?e a?n?d f?o?r?c?e?d v?i?b?r?a?t?i?o?n, e?c?c?e?n?t?r?i?c?i?t?y -
Pages 73-82In this paper, vibration performance analysis of a nonlinear displacement-velocity-dependent (NDVD) damper is presented. The proposed NDVD damper is constructed using the appropriate changing in the structure of a linear damper which results the damping coefficient of the proposed NDVD damper varies respect to the displacement and the velocity of damper piston. To this end, a solid cone shaped part is assembled in the interior region of the damper cylinder, which causes the fluid moves between the solid cone shaped part and inside the existing orifice on the piston. In fact, the movement of the piston results in changing the size of the gap where the fluid passes and the damping coefficient is consequently varied. In order to obtain more accurate modeling in the vibration analysis, the effect of momentum variation is also applied in the advised NDVD damper. The effect of momentum variation on the motion of a vibratory system equipped with a nonlinear displacement-velocity-dependent (NDVD) damper is elaborated and also compared with the previously published papers. In this paper, the governing equation of a mass-spring system equipped with the NDVD damper as the vibratory system is derived for three cases of free, forced and resonance vibration problems and solved by the numerical fourth-order Runge-Kutta method. The displacement profile, velocity profile, damping force and the force transmitted to the base of the system are evaluated for a mass-spring system equipped with the NDVD damper. In addition, these results for three cases of free, forced and resonance vibration problems are compared with the results obtained from the system equipped with a linear damper as well as the nonlinear displacement-dependent (NDD) damper presented in the previous works. The simulation results confirm that the recommended NDVD damper has much better performance in reducing of vibration in the system compared to the linear and NDD dampers.Keywords: free vibration, forced vibration, resonance vibration, nonlinear displacement-velocity-dependent damper, law of conservation of momentum
-
Pages 83-91Diaphragm pumps are positive displacement pumps which have many applications in the petrochemical, and gas industries. As an example, Infusion pumps can be mentioned which are highly regarded in the gas industry due to the good resistance against chemical fluids. Since the diaphragm pumps are composed of various mechanical parts, some of which, such as the diaphragm, are in direct contact with the fluid, many different causes of mechanical damage are reported from some consumer companies such as Gas Company for this purpose, finding a model similar to the actual model is very useful. One of these pump's design and manufacturing methods is using commercial codes for simulation rather sophisticated and expensive laboratory methods. Since the fluid in the pump is transmitted by a diaphragm motion, the concept called the fluid structure interaction is defined due to the problems related to simulations of fluid structure interaction, animated network simulation, and geometry of the pumps, limited deal of efforts has been done in the past for numerical analysis of these pumps. Today, with significant progress made in the development of computational systems and commercial codes, a good platform for the simulation of such problems is created. There are several methods for simulating fluid structure interaction problems; one-way method is selected for this simulation due to the small deformation of the diaphragm and flow fields in front of other aspects of the model pump. In order to reduce the size of the pump dimensional model calculations, this pump is simulated using ANSYS CFX commercial code. We have generated a model that could well show some parameters of this type of pump, and so, a more efficient model can be produced by reduced construction costs via future studies. One of the results of the presented method, is introducing one-way fluid structure interaction method as a suitable modeling method. The other results worthy of being mentioned are the study on the velocity and pressure fields, the effects of functional parameters such as engine speed and displacement diaphragm pump on stream, and other outcomes that are fully addressed in a season. In order to validate the model the boundary conditions of a real sample fluid injection pump, odorant in city gas company, is used; that after comparing the amount of output in terms of displacement diaphragm with the information contained in the pump catalog, in the worst case, error rate turns out to be 10%, and an average error is about 5%.Keywords: Diaphragm pump, fluid structure interaction, ansys CFX
-
Pages 93-99Nowadays, CPUs and GPUs are used in computations pertaining to numerical solution of differential equations. However, the fixed hardware architecture of CPUs and GPUs makes it difficult to optimally implement many numerical solution algorithms. In recent years, a new method, based on hardware implementation of equations using Field Programmable Gate Array (FPGA), has been given much attention. The unique feature of this approach is the ability to vary the hardware architecture on the basis of the solution algorithm, which results in increased solution speed and a reduction in power consumption. This methodology, in which hardware can vary from one architecture to another for computing purpose is named Reconfigurable Computing (RC). RC can be used to solve a lot of problems such as FEM, FVM with structured or unstructured mesh.In this research, typical problems, such as mass-spring systems and wave equations, have been considered, and hardware implementation on FPGA has been used to solve the resulting differential equations. For modeling these systems, we used the software and hardware which is accessible to us, so we used a domestic FPGA board and MatLab and Xilinx ISE software products. Based on the results, advantages and challenges for hardware implementation of differential equations have been presented. Results for a single element mass-spring system show a comparable solution speed for CPU and FPGA implementation. However, with an increase in the number of elements of the mass-spring system, for example, to 6, the FPGA hardware implementation overtakes CPU and the speed of FPGA becomes almost 8 times that of CPU. Moreover, results of the solution of wave equations show that the speed with FPGA implementation is 3.6 times that of CPU. Therefore, for higher numbers of computational elements, results show the superior process speeds attainable with hardware implementation of equations using FPGA compared to the software mplementation on CPU.Keywords: R?e?c?o?n?f?i?g?u?r?a?b?l?e c?o?m?p?u?t?i?n?g, s?o?l?u?t?i?o?n s?p?e?e?d u?p, P?D?E, O?D?E
-
Pages 101-120Fatigue design of helicopter components has proven to be a difficult and challenging task. The purpose of the fatigue evaluation of helicopter components, especially the main rotor blade, is to show that catastrophic failure expectation during its service life due to fatigue is completely gone; in addition, occurrence of Non-catastrophic cracking remains low enough so that the economic use of the helicopter structure can be achieved. The fatigue design methodology, most commonly applied by the helicopter community, was based on the Safe-Life philosophy. In spite of safety and the overall success in helicopter applications, this method does not account for any component strength that deviates from the strength distribution assumption made during the fatigue substantiation process. In recent years, due to low efficiency of Safe-Life method, using other fatigue life analysis methods, such as flaw tolerance, damage tolerance, and fault tolerance, have been felt to be more necessary.The Flaw Tolerant Safe-Life or Enhanced Safe-Life method provides component management requirements based on the assumption of the existence of flaws in the component's critical areas. This approach is adopted only in the helicopter community. Flaw Tolerant method is based on traditional safe-life design methodology that uses special S-N curves obtained from specimens containing some defects (flaws). Damage tolerance requires that the structures retain, after a partial failure, the capability to withstand the limit load. Fault tolerance is a new damage tolerance design method which is based on equivalent initial flaw-sized concept. Since 1989, the Airworthiness Regulation evolved towards the application of Damage Tolerance principles to rotorcraft. This change forced the helicopter industries to review their design methodologies and to face new problems, linked with fracture mechanics applications to their typical structures.In this paper, various approaches to helicopter fatigue design are reviewed, and the advantages and disadvantages of each method are discussed. Then, different methods of helicopter fatigue design are compared. At the end, other aspects of helicopter fatigue design, such as influence of material on helicopter fatigue design, fatigue design of helicopter components against impact loads, and conducting tests in relation to the helicopter fatigue design are all discussed.Keywords: H?e?l?i?c?o?p?t?e?r f?a?t?i?g?u?e, f?a?t?i?g?u?e d?e?s?i?g?n, h?e?l?i?c?o?p?t?e?r f?a?t?i?g?u?e l?i?f?e, h?e?l?i?c?o?p?t?e?r f?a?t?i?g?u?e a?p?p?r?o?a?c?h?e?s
-
Pages 121-127In this paper, a novel technique is presented for inverse kinematics and motion planning of a redundant manipulator robot in an environment with unknown obstaclesusing a fuzzy controlling is presented. Kinematic redundancy occurs when amanipulator possesses more degrees of freedom than the minimum number requiredfor executing a given task. Redundancy enhances the manipulator dexterity andflexibility which allows the redundant robot to move faster and safer in theenvironment without colliding with obstacles. In order to avoid colliding withobstacles, a high degree of freedom robot was used. Due to high degree of freedom, inverse kinematics of redundant robots is very difficult, thus a general approach to motion planning of a redundant manipulator robot is very practical and valuable. It was inspired that a human arm is capable of avoiding colliding obstacles. Therefore, in this paper, direct control of end effector position of manipulator using a multi- behavior fuzzy controller, inspired by behavior of human arm, makes a practical method to the navigation of redundant manipulator robots. In this method, the control of every link is independent from the degree of freedom of robot; the number of input and output signals are constant. Fuzzy controller system used in this research is a combination of three fuzzy controllers, which deals with a separate behavior of redundant robot. The mainobjective is still to avoid the obstacles and flexion and extension of arm. The final behavior of redundant robot is a combination of these behaviors. For illustration, some simulation results of redundant planar manipulator moving in an unknown environment is presented. Results were prepared by a Simulink model containing fuzzy control subsystems, sensor, actuators, and obstacles. The simulation and experimental results of three and six link planar manipulators in environment with one obstacle and without obstacle show a good and promising performance of the robot.Keywords: M?o?t?i?o?n p?l?a?n?n?i?n?g, r?e?d?u?n?d?a?n?t r?o?b?o?t, f?u?z?z?y c?o?n?t?r?o?l, u?n?k?n?o?w?n e?n?v?i?r?o?n?m?e?n?t
-
Pages 129-136In the present study, a comprehensive thermodynamic modeling and optimization of CGAM problem is presented. The CGAM problem refers to a cogeneration plant which delivers 30 MW of electricity and 14kg/s of saturated steam at 20 bar. The installation consists of a gas turbine followed by an air preheater that uses part of the thermal energy of the gases leaving the turbine, and a heat-recovery steam generator in which the required steam is produced. This system is composed of air compressor, combustion chamber (CC), Air Preheater, Gas Turbine (GT), and a Heat Recovery Heat Exchanger. In this paper, at the first stage, each part of the system is modeled using thermodynamic laws; and next, with by applying economic functions, the optimization of this problem is performed. For optimization, objective functions includes the total cost rate of the system product. The environmental conditions are defined as T0 = 298.15K and P0 = 1.013 bar. The fuel for the total plant is natural gas (taken as methane) with a lower heating value (LHV) which is equal to 50000 kJ/kg. And then, solve the problem which is formulated as a set covering problem by Genetic algorithm and PSO algorithm is solved. In the end of this article, we compare these solving approaches (Genetic and PSO algorithms) to know which of them are working efficiently. The design parameters of this cycle are compressor pressure ratio $(r_{AC})$, compressor isentropic efficiency $(eta_{AC})$, GT isentropic efficiency $(eta_{GT})$ , CC inlet temperature $(T_3)$, and turbine inlet temperature $(T_4)$. After reviewing the results of the two algorithms, it is showed that both algorithms which to optimize the results are almost identical. However, the PSO algorithm is simple to implement and more flexible in programmingand convergence rate than compared to the capability of Genetic algorithm is capable. The results show that the PSO algorithm is more efficient than Genetic algorithm in solvinge CGAM problem.Keywords: P?S?O a?l?g?o?r?i?t?h?m, g?e?n?e?t?i?c a?l?g?o?r?i?t?h?m, o?p?t?i?m?i?z?a?t?i?o?n, C?G?A?M p?r?o?b?l?e?m
-
Pages 137-145Shape memory polymers are a class of multi-phase smart materials which have the ability to return from a deformed state (temporary or fixed shape) to their original (or permanent) shape, called as shape memory effect, (or recovery) under different thermo mechanical cycles, e.g., fixed strain stress recovery and fixed stress strain recovery. Due to their unique behavior, shape memory polymers have many applications in industry areas. Shape memory polymers have been researched, developed, and utilized in a wide range of applications such as advanced technologies in the aerospace, medical and oil exploration industries. Moreover, shape memory polymers have a promising future for application in sensors, actuators and smart devices. However, applications of shape memory polymers are restricted by their low strength. Different techniques are employed to eliminate such restrictions. Among them, addition of micro and/or nano-particles is a common practice. In this study, a numerical method, based on 3D finite element method, is introduced to investigate the effect of nano-particles on mechanical properties (e.g., the mechanical strength) and performance of shape memory polymer nano-composites. The non-linear behavior of shape memory polymers is described through employing a recently proposed visco-hyper-elastic constitutive model, and the nano-composite is simulated in the framework of the nonlinear finite element method. Effects of different volume fractions and aspect ratios of the nano-particles are investigated, and the results are presented in the form of stress strain temperature diagrams. According to the produced results, increasing the volume fraction and/or aspect ratio increases the generated elastic stress and the recovered stress. In addition, adding up to 3 percent of nano-particle volume fraction and applying strains up to 20 percent would not disrupt the performance of the material, while remarkably enforce the shape memory polymer based nano-composite.Keywords: S?h?a?p?e m?e?m?o?r?y p?o?l?y?m?e?r n?a?n?o?c?o?m?p?o?s?i?t?e, v?i?s?c?o?e?l?a?s?t?i?c m?o?d?e?l?i?n?g, f?i?n?i?t?e e?l?e?m?e?n?t m?e?t?h?o?d, g?r?a?p?h?e?n?e n?a?n?o-p?l?a?t