جستجوی مقالات مرتبط با کلیدواژه « coupler » در نشریات گروه « برق »
تکرار جستجوی کلیدواژه «coupler» در نشریات گروه «فنی و مهندسی»-
Scientia Iranica, Volume:30 Issue: 3, May-June 2023, PP 1139 -1147In this paper, some hidden aspects of composite right-/left-handed (CRLH) transmission lines (TLs) and couplers are clarified. Complete and detailed dispersion analysis of an isolated CRLH TL is presented including lossless and lossy cases based on a conventional unit cell, devised formerly. Dispersion analysis of CRLH TLs is extended form the conventional to an accurate unit cell. Capability of TLs consisting of such unit cells in supporting RLH waves is demonstrated. A pure analytical strategy is proposed for parameter extraction of CRLH TLs and symmetric couplers based on accurate circuit models. It is shown that by including loss parameters in the circuit model, there is no need to make use of curve fitting methods for parameters extraction of said couplers.Keywords: Coupler, dispersion analysis, parameter extraction, left-handed, metamaterial, transmission line}
-
در این مقاله با استفاده از تشدیدکنندههای T شکل و امپدانس پلهای، یک تزویجکننده میکرواستریپی جدید با فرکانس کاری یک گیگاهرتز ارایه شده است. تزویجکننده پیشنهادی نسبت به تزویجکنندههای پیشین از اندازه کوچکتری برخوردار بوده و عملکرد مطلوبی از خود نشان میدهد. تزویجکننده طراحیشده در مقایسه با تزویجکننده شاخهای متداول دارای 65% کاهش سایز میباشد و همچنین هارمونیکهای دوم تا هفتم را نیز حذف میکند. تزویجکننده طراحیشده بر روی زیرلایه 5880 RT/duroid با ثابت دیالکتریک 2/2، ضخامت mil 31 و تانژانت تلفات 0009/0 ساخته شده است. نتایج اندازهگیری و شبیهسازی تطبیق خوبی دارند که نشان از صحت طراحی قطعه دارد.
کلید واژگان: تزویج کننده, تشدیدکننده T شکل, تشدیدکننده امپدانس پلهای و حذف هارمونیک}In this paper a novel compact microstrip coupler using T-shaped and stepped impedance resonators is proposed, simulated and fabricated. In the proposed structure long quadrature wavelength lines are replaced with small resonators, which results in size reduction and harmonics suppression. The proposed coupler correctly works at 1 GHz and suppresses 2nd up to 7th unwanted harmonics. Moreover the designed coupler reduces the circuit size more than 65% compared to the conventional coupler.
Keywords: Coupler, size reduction, harmonic suppression, resonator} -
این مقاله به بررسی و تحلیل و طراحی تزویجگر (پیوننده) نامتقارن چندبخشی با امپدانس های پایان دهی متفاوت می پردازد. ساختار یک پیوننده خط کوپل شده مورد تحلیل و بررسی قرارگرفته است. در ابتدا ماتریس امپدانس آن استخراج شده است. در ادامه ماتریس انتقال به دست آمده، سپس ماتریس انتقال یک پیوننده جهتی نامتقارن چندبخشی بر اساس مشخصات آن، استخراج شده است. درنهایت ماتریس انتقال کلی تزویجگر (پیوننده) به ماتریس امپدانس آن تبدیل شده، و سپس ماتریس پراکندگی آن استخراج شده است. از روش حد اقل مربعات کاهش یافته به منظور طراحی تزویجگر (پیوننده) جهتی نامتقارن استفاده شده است. تابع خطا، که خود تابعی از ابعاد فیزیکی ساختار می باشد، بر اساس پارامترهای پراکندگی پیوننده جهتی نامتقارن تشکیل شده است. ابعاد فیزیکی ساختار (طول و پهنای خطوط و فاصله ی میان آن ها) با کمینه سازی تابع خطا به وسیله کد نوشته شده در نرم افزار MATLAB و استفاده از الگوریتم ژنتیک (GA) و الگوریتم گرادیان مزدوج (CGM) به دست می آید، سپس نرم افزار تحلیل تمام موج HFSS به منظور نهایی کردن ساختار بهینه تزویجگر (پیوننده) جهتی نامتقارن مورداستفاده قرارگرفته است. درنهایت یک مثال از تزویجگر (پیوننده) جهتی نامتقارن بر روی زیرلایه Rogers 4003 طراحی و ساخته شده، که نتایج اندازه گیری آن با نتایج شبیه سازی تطابق دارد .ضریب تزویج (پیوند) این ساختار 6 dB می باشد و در بازه فرکانسی 5.2 - 6.2 GHz با امپدانس های پایان دهی 50، 50، 75 و 100 اهم طراحی شده است.
کلید واژگان: پیوننده, پیوننده جهتی, پیوننده جهتی نامتقارن, پیوننده چندبخشی جهتی نامتقارن, تطبیق امپدانس}Journal of Iranian Association of Electrical and Electronics Engineers, Volume:17 Issue: 3, 2020, PP 101 -107This paper presents the analysis and design of an asymmetrical directional coupler (ADC) with arbitrary source and load impedances. The microstrip-coupled-line structure is analyzed and its impedance matrix is first obtained. Its transmission matrix is then determined. The transmission matrix of multi-section ADC is then obtained using its properties. Finally, the total transmission matrix is converted to the impedance matrix and then its scattering matrix is derived. The method of least squares (MLS) is applied for the design of ADC. An error function is constructed based on the scattering parameters of ADC, which is a function of its geometrical dimensions. The minimization of the error function determines its dimensions (namely widths and lengths of line sections and their spacings) by writing a software in MATLAB using the Genetic Algorithm (GA) and Conjugate Gradient Algorithm (CGM). The HFSS Full Wave Software is applied to finalize the optimum design of the ADC configuration. An example of the ADC is designed, fabricated (on the substrate ROGERS 4003) and measured as the proof of concept. Its coupling coefficient is 6 dB, frequency band is 5.2-6.2 GHz, terminal impedances are 50, 50, 75 and 100 Ohms.
Keywords: Coupler, Directional Coupler, Asymmetric Directional Coupler, Multi-Section Asymmetrical Directional Coupler, Impedance Matching} -
A new shaped circularly polarized dielectric resonator antenna (CP DRA) is studied with branch-line coupler and log-periodic balun for the GPS application. Since the coupler and balun are located under the DRA, it does not increase the footprint of the antenna, as a result the system is very compact. Two configurations are considered in this paper. In the first configuration, an external 50Ω load is used for the matching port of the branch-line coupler. For the second one, a three-resonator log-periodic balun is used instead of branch-line coupler, thus, no lumped elements are required in this configuration. Moreover, two modes HEM11δ of the cylindrical DRA are utilized to design the wide band circular polarization. The reflection coefficient, axial ratio, antenna gain, and radiation pattern are studied for each configuration. These first and the second configurations offer an impedance bandwidth (S11Keywords: Circular polarization, dielectric resonator antenna, coupler, balun}
-
یوننده های جهتی، عناصر غیر فعالی هستند که برای تقسیم یا ترکیب توان درمدارهای مایکروویو و موج میلیمتری و تراهرتز کاربرد زیادی دارند. با استفاده از تکنیک موجبر مجتمع شده در زیرلایه، این قطعه مایکروویوی به صورت هم زمان از بسیاری ویژگی های خوب مدارهای چاپی و موجبر مستطیلی از قبیل هزینه کم، سایز کوچک و تلفات انتقالی و تلفات تشعشعی بسیار کم برخوردارخواهد شد. در این مقاله سه نمونه پیوننده خط شاخه ای با استفاده از تکنیک موجبر مجتمع شده در زیرلایه طراحی و برای افزایش پهنای باند فرکانسی آن از روش چندبخشی سازی بهره گرفته شده است. برای بهینه سازی تحلیل مداری از روش حداقل مربعات استفاده و در تمام مراحل طراحی پیوننده بصورت نامتقارن و مقدار پیوند دلخواه درنظرگرفته شده است. سپس نتایج حاصل از تحلیل مداری با نتایج تحلیل تمام موج مقایسه شده است و یک نمونه پیوننده دو بخشیdB 3 برای کاربرد در باند Ku طراحی و ساخته شده است. مشاهده می شود که تطابق خوبی بین نتایج اندازه گیری و شبیه سازی وجود دارد.
کلید واژگان: پیوننده, چندبخشی, موجبر مجتمع شده در زیرلایه, روش حداقل مربعات, گرادیان مزدوج}Journal of Iranian Association of Electrical and Electronics Engineers, Volume:12 Issue: 2, 2015, P 85Directional couplers are passive devices which are used as power dividers and combiners in microwave, millimeter and terahertz systems. By the use of substrate integrated waveguides (SIW) for the design of such devices, the advantages of waveguide and printed circuit (PC) technologies are utilized simultaneously, such as low cost, small size, low transmission and radiation losses. In this paper, the method of least squares is employed for the design and optimization of symmetrical and asymmetrical multi-section branch-line-couplers incorporating impedance matching at its input and output ports. The equivalent circuit of the branch-line coupler is obtained and its transmission and scattering matrices are derived, which are eventually used for the construction of an error function. Its minimization leads to the determination of the dimensions of the coupler and its optimum design. The design specifications of coupler include its power division ratios, port impedances and frequency bandwidth. Three prototype models of branch-line-couplers are designed, namely a 6dB singlesection coupler, a symmetrical 3dB two-section coupler and an asymmetrical 3dB two-section coupler. The latter coupler is fabricated and measured. The designs of couplers are verified by the HFSS full-wave computer software with very good agreement.Keywords: Coupler, Multi, section, Substrate integrated waveguide, Method of least square, Gradient conjugate}
- نتایج بر اساس تاریخ انتشار مرتب شدهاند.
- کلیدواژه مورد نظر شما تنها در فیلد کلیدواژگان مقالات جستجو شدهاست. به منظور حذف نتایج غیر مرتبط، جستجو تنها در مقالات مجلاتی انجام شده که با مجله ماخذ هم موضوع هستند.
- در صورتی که میخواهید جستجو را در همه موضوعات و با شرایط دیگر تکرار کنید به صفحه جستجوی پیشرفته مجلات مراجعه کنید.