به جمع مشترکان مگیران بپیوندید!

تنها با پرداخت 70 هزارتومان حق اشتراک سالانه به متن مقالات دسترسی داشته باشید و 100 مقاله را بدون هزینه دیگری دریافت کنید.

برای پرداخت حق اشتراک اگر عضو هستید وارد شوید در غیر این صورت حساب کاربری جدید ایجاد کنید

عضویت

جستجوی مقالات مرتبط با کلیدواژه « زیربالاست » در نشریات گروه « عمران »

تکرار جستجوی کلیدواژه «زیربالاست» در نشریات گروه «فنی و مهندسی»
  • عطا آقایی آرایی*

    این مقاله رفتار مونوتونیک-پساسیکلی سرباره های فولاد و اصلاح شده با ژیوگرید و خرده-لاستیک به عنوان بالاست و زیربالاست خطوط راه آهن و مقایسه آنها با بالاست آهکی را ارایه می دهد. نتایج شامل تنش تفاضلی حداکثر، مدول سکانتی  و مدول باربرداری-بارگذاری مجدد ، زاویه اصطکاکو شکست دانه می باشد. مقادیر زاویه اصطکاک نمونه های بالاست، زیربالاست و بالاست/ زیربالاست سرباره ای مشابه مصالح معمول است. وجود لایه های ژیوگرید در بالاست سبب افزایش جزیی زاویه اصطکاک و ضریب پواسن می شود. وجود زیربالاستسرباره ای،مقدار فاکتور شکستبالاست، حداقل 2 برابر می کند. براساس شاخص کثیفی و شکست لایه های بالاست سرباره ای تحت بارگذاری مونوتونیک-پساسیکلی نسبتا تمیز می باشد. غرقاب شدن سبب افزایش شکست دانه ها و کاهشمی شود. با توجه کاهش شدید مقادیر مدول مخلوط با خرده لاستیک بالاست، علیرغم تاثیر در کاهش شکست دانه ها، استفاده از خرده لاستیک توصیه نمی شود. براساس نتایج می توان از مصالح سرباره به عنوان بالاست و زیربالاست به جای مصالح متداول استفاده کرد.

    کلید واژگان: سرباره ها, بالاست, زیربالاست, مونوتونیک-پساسیکلی, ژئوگرید, خرده لاستیک}
    Ata Aghaei Araei *

    This paper presents post-cyclic-monotonic behavior of BOF and EAF steel slags as ballast and subballast layers with and without geogrid or tire chips, and comparing their behavior with limestone material. Tests were carried out by the large scale triaxial equipment. The confining pressures are chosen with respect to the stress levels in typical rail road track. The tested specimens were prepared by maximum dry density. The used square shape geogrid has aperture sizes of 25*30.5 mm and the depth of placement about 5cm above and middle of subballast. Size of tire chips was 12.7-25 mm and mixed 7% by weight, only in ballast layer. Maximum deviatoric stress, secant modulus, unloading-reloading modulus, friction angle and particle breakage are investigated. Results indicated that performing cyclic loading on ballast layer before the post cyclic-monotonic tests decreases the axial strain corresponding to maximum deviatoric stress. Post-cyclic-monotonic friction angle of ballast and subballast with and without geogrid ranges from 57-65°. The friction angles of the steel slag of ballast, subballast and ballast/subballast specimens are similar to traditional ballast materials. The values of and decrease as moisture of specimen increases. Average poison ratio for mention layers is about 0.3. Marsal breakage index (Bg) of the single layered steel slag ballast is almost two times of the limestone ballast. Presence of steel slag subballast increases Bg of the steel slag ballast to about 2 times. According to fouling and breakage indexes of steel slag ballast under post cyclic-monotonic loading is relative clean. Saturation of ballast specimen causes increase of particle breakage, therefore the drainage of ballast materials is necessary. Usage of tire chips is not recommended in ballast due to high rate of decreasing of modulus and friction angle. Results indicated that the steel slag particle may be used as natural aggregate in ballast and subballast layers.

    Keywords: Slags, Ballast, Sub-ballast Post-cyclic-monotonic, Geogrid, Tire-chips}
نکته
  • نتایج بر اساس تاریخ انتشار مرتب شده‌اند.
  • کلیدواژه مورد نظر شما تنها در فیلد کلیدواژگان مقالات جستجو شده‌است. به منظور حذف نتایج غیر مرتبط، جستجو تنها در مقالات مجلاتی انجام شده که با مجله ماخذ هم موضوع هستند.
  • در صورتی که می‌خواهید جستجو را در همه موضوعات و با شرایط دیگر تکرار کنید به صفحه جستجوی پیشرفته مجلات مراجعه کنید.
درخواست پشتیبانی - گزارش اشکال