به جمع مشترکان مگیران بپیوندید!

تنها با پرداخت 70 هزارتومان حق اشتراک سالانه به متن مقالات دسترسی داشته باشید و 100 مقاله را بدون هزینه دیگری دریافت کنید.

برای پرداخت حق اشتراک اگر عضو هستید وارد شوید در غیر این صورت حساب کاربری جدید ایجاد کنید

عضویت

جستجوی مقالات مرتبط با کلیدواژه « bubble column » در نشریات گروه « مهندسی شیمی، نفت و پلیمر »

تکرار جستجوی کلیدواژه «bubble column» در نشریات گروه «فنی و مهندسی»
  • محمدمهدی کیب اللهی، پیمان کشاورز*

    با توجه به اهمیت حذف بخار آب موجود در گازهای طبیعی، دست یابی به یک جاذب پرقدرت در فراوری گازهای طبیعی بسیار ضروری به نظر می رسد. در این تحقیق، برای نخستین بار از جاذب تترا اتیلن گلایکول (TREG) و ترکیب آن با تری اتیلن گلایکول (TEG) برای حذف بخار آب از جریان هوای مرطوب استفاده شد. در ادامه، برای دست یابی به بینشی صحیح از عمل کرد TREG، نتایج به دست آمده با جاذب خالص TEG مقایسه و تاثیر دبی جریان هوا نیز در نظر گرفته شد. با توجه به نتایج، تمامی جاذب های به کار گرفته شده در این تحقیق، عمل کردی بهتر در دبی های پایین تر داشت. هم چنین،در حالی که TEG جاذبی بهتر در دبی های پایین تر بوده است، TREG عمل کردی بسیار بهتر در میزان حذف بخار آب در دبی های بالاتر داشته است. در نهایت، در بهترین شرایط عملیاتی لحاظ شده در این تحقیق، استفاده از TEG در دبی 60 میلی لیتر بر دقیقه منجربه کاهش رطوبت ورودی هوا از 90% به حدود 10% شد. حال آن که، استفاده از TREGدر دبی 120 میلی لیتر بر دقیقه نتایج بهتری را به همراه داشت و میزان حذف را به مقداری در حدود 5% کاهش داد. میزان بالای جذب بخار آب در دبی های بالا، نشان دهنده قابلیت بالای TREG در به کارگیری در فرایندهای شیرین سازی در مقیاس صنعتی دارد.

    کلید واژگان: برج حبابی, تترا اتیلن گلایکول, تری اتیلن گلایکول, نم زدایی}
    Mohammad Mehdi Kaibollahi, P. Keshavarz *

    According to the importance of water vapor available in the natural gas, achieving a powerful absorbent looks quite necessary. In this study, for the first time, tetraethylene glycol (TREG) and its mixture with triethylene glycol (TEG) were used to remove water vapor from a wet air stream. Following this, to achieve a good vision about the performance of TREG, the results were compared with the pure TEG and the impact of gas flow rate was considered. Based on the obtained results, all absorbents applied in this work resulted in a better performance in lower gas flow rates. Further, although TEG was the best absorbent at low gas flow rates, TREG had the best performance in water vapor removal at high gas flow rates. Finally, in the best operational condition in this work, the use of TEG led to the reduction of water vapor from 90% to about 10% at 60 ml.min-1. However, applying TERG had a better result at 120 ml.min-1 and caused the water vapor to reduce from 90% to approximately 5%. High water vapor absorption in high flow rates indicates the high capability of TREG to employ in gas dehydration processes in industrial scales.

    Keywords: Bubble column, Treg, TEG, Dehumidification}
  • Hasan Pashaei, Fahimeh Mirzaei, Ahad Ghaemi *
    In this study, the effective parameters in mass transfer in the process of gas absorption in the bubble column by amine solvents have been investigated. Also, the aim of this study is to present a general and accurate correlation with the least simplifying assumptions to calculate the mass transfer flux of gas phase to liquid phase components in three electrolyte systems MDEA-Pz, MEA-Pz, and MEA-MDEA. The effect of parameters on mass transfer such as retention time, apparent gas velocity, liquid phase properties, operating conditions, type of distributor, and bubble characteristics was analyzed. Effective parameters were expressed to achieve functional correlations using dimensionless numbers by using the pi-Buckingham theorem. The correlation coefficients for MDEA-Pz, MEA-Pz, and MDEA-MEA were obtained at 0.951, 0.981, and 0.924, respectively. The mean relative error obtained from predicting the mass transfer flux correlation for all three MDEA-Pz, MEA-Pz, and MDEA-MEA amine combination systems was 3.6, 4.5, and 4.8%, respectively. The results showed that the proposed correlations for mass transfer flux compared to other correlations have high accuracy.
    Keywords: absorption, carbon dioxide, Mass transfer flux, amine solution, Bubble column, pi-Buckingham}
  • نگین محمدزاده، فرزانه رفیعیان، مسعود حق شناس*، محسن نصر اصفهانی، تورج توکلی
    اثر میدان مغناطیسی بر جذب دیوکسید کربن توسط آب دیونیزه و نانوسیالات آب/اکسید آهن و آب/اکسید آلومینیوم در یک ستون حبابی مورد مطالعه قرار گرفت. علاوه بر شدت میدان مغناطیسی، اثر پارامترهای کلیدی مثل دبی جریان گاز، نوع نانوذره، جهت میدان و غلظت نانوسیال بر مقادیر ضریب و شار انتقال جرم بررسی شد. نتایج نشان داد با توجه به قطبی بودن ملکولهای آب، با افزایش شدت میدان مغناطیسی تا 1133 گوس، ضریب انتقال جرم در آب خالص به میزان 7/6 % افزایش میابد. این افزایش در صورتی حاصل می گردد که جهت میدان همراستا با جهت حرکت فاز پیوسته باشد. در صورت اضافه نمودن نانوذرات به آب خالص، ضریب و شار انتقال جرم افزایش میابد. با افزایش غلظت نانوسیال آب/ اکسید آهن ضریب انتقال جرم نیز افزایش یافت، ولی در مورد نانوسیال آب/اکسید آلومینیوم با افزایش غلظت نانوسیال تا 005/0 درصد حجمی، ضریب انتقال جرم نسبت به آب خالص افزایش پیدا کرد، اما با افزایش غلظت، ضریب انتقال جرم کاهش یافت.
    کلید واژگان: جذب گاز, برج حبابی, نانوسیال, میدان مغناطیسی}
    Negin Mohammadzadeh, Farzaneh Rafieian, Masoud Haghshenasfard *, Mohsen Nasr Esfahany, Touraj Tavakoli
    Effect of magnetic field on the CO2 absorption in deionized water, water/Fe3O4, and water/Al2O3 nanofluids in a bubble column is studied. Effect of the other key parameters such as gas flowrate, nanoparticle type, magnetic field direction, and nanofluid concentration on the mass transfer rate and mass transfer coefficient has also been investigated. The results showed according to the polar nature of the water moleculs, by increasing the magnetic fielt to 1133 gauss, the mass transfer coefficient in pure water increases up to 6.7%. The enhancement can be achieved if the direction of the magnetic filed is parallel to the direction of the continious phase. By adding the nanopaticles to the pure water, the mass transfer coefficient and mass transfer rate increses. By increasing the water/Fe3O4 concentration the mass transfre coefficient increases, but in the water/Al2O3 nanofluid, by incerasing the nanofluid concentration up to 0.005%, the mass trasnfer coefficient increases, and then decreases.
    Keywords: Gas absorption, Bubble column, Nanofluid, Magnetic field}
  • Jamshid Behin, Negin Farhadian*
    In this work, response surface methodology (RSM) and artificial neural network (ANN) were used to predict the decolorization efficiency of Reactive Red 33 (RR 33) by applying the O3/UV process in a bubble column reactor. The effects of four independent variables including time (20-60 min), superficial gas velocity (0.06-0.18 cm/s), initial concentration of dye (50-150 ppm), and pH (3-11) were investigated using a 3-level 4-factor central composite experimental design. This design was utilized to train a feed-forward multilayered perceptron artificial neural network with a back-propagation algorithm. A comparison between the models’ results and experimental data gave high correlation coefficients and showed that the two models were able to predict Reactive Red 33 removal by employing the O3/UV process. Considering the results of the yield of dye removal and the response surface-generated model, the optimum conditions for dye removal were found to be a retention time of 59.87 min, a superficial gas velocity of 0.18 cm/s, an initial concentration of 96.33 ppm, and a pH of 7.99.
    Keywords: Artificial neural network, Bubble column, Ozone, Ultraviolet, Response surface method, Reactive red 33}
  • Rahbar Rahimi, Somayeh Hajghani
    Bubble columns are gas- liquid contactors that are widely used in chemical and bio- chemical industries. High mixing that result in high heat and mass transfer rates are amongst their advantages. Heat transfer in a bubble column having a bundle of heaters investigated and the variation of heat transfer coefficient with variation in heaters pitch to diameter ratios in a bundle of heaters reported. The bubble column modeled in a three-dimensional in the Eulerian framework by using computational fluid dynamic simulation. It was 0.292 m in diameter and 1.5 m in height. Simulations performed for five heaters and for nine heaters in a bundle. The bubble column with a five heaters bundle was investigated in the pitch to diameter ratios of 1.5, 2 and 2.5. The bubble column with nine heaters bundle was investigated with the pitch to diameter ratios of 1.25, 1.5, 2.25 and 2.46. The range of the gas velocity was 0.0025 to 0.04 m/s. The heat transfer results show that, with decreasing the pitch to diameter ratios the heat transfer coefficient decreases. In bubble column with bundle of nine heaters at a constant superficial gas velocity, with decreasing the pitch to diameter ratio from 2.46 to 1.5 the heat transfer coefficient decreases; whereas in the pitch to diameter ratio of 1.25 heat transfer coefficient is high.
    Keywords: Bubble column, Bundle of heaters, CFD, Heat transfer, Hydrodynamics, Pitch to diameter ratios}
  • M. Pirdashti, R. Kompany
    Experimental measurements of overall gas holdup (εg), residence time distribution (RTD) and liquid mixing time (tm) have been carried out in an air-water system in a 17 lit bubble column with an 11 cm diameter, over a wide range of superficial gas velocity (0.14-1.46 ms-1) and height to diameter ratio (1.36-8.84). The bed expansion method was used to obtain holdup values and the change of slope related to εg versus superficial gas velocity (Usg) indicated the transition point from homogeneous to heterogeneous regime at Usg= 0.7-0.9 ms-1. Besides, the experiments illustrated that H/D ratio had no effect on holdup values. The axial dispersion model was used with semi-closed boundary conditions for prediction of RTD, and hence, the axial dispersion coefficients (Dax). Moreover, fitting results of the model and experimental RTD curves achieved from tracer injection method attained the model parameter, Dax , in three H/D ratios of 4.73, 6.36 and 8.84. Results showed that an elevation in H/D ratio, caused a rise in Dax. On the other hand, the mixing time data declined with an increase in Usg; however enhancement of H/D ratio caused an increase in tm.
    Keywords: Bubble column, Overall gas holdup, Residence time distribution, Axial dispersion coefficient, Mixing time}
  • بهنوش مشتری *، انسیه گنجی، جعفر صادق مقدس

    ماندگی گاز یکی از عوامل مهم برای پیشگویی رفتار هیدرودینامیکی در راکتورهای حبابی است. از عوامل موثر بر ماندگی گاز، نوع توزیع کننده گاز و ارتفاع ستون مایع است. در این تحقیق از یک ستون استوانه‌ای به قطر cm 15 و مجهز به دو نوع توزیع کننده گاز، استفاده و اثر توزیع کننده گاز و ارتفاع ستون مایع در سرعت‌های متفاوت گاز بررسی شدند. نتایج آزمایش‌ها نشان می‌دهد که، افزایش ارتفاع ستون مایع و کاهش قطر منافذ توزیع کننده گاز، باعث افزایش ماندگی کلی گاز در سیستم می‌شود.

    کلید واژگان: ستون حبابی, توزیع کننده گاز, ماندگی گاز}

    Gas hold up in bubble column reactors is one of the important parameter to predict hydrodynamic behavior in bubble column reactors. Since sparger type and liquid height have important effect on total gas hold up, In this study a cylindrical bubble column with 15 cm diameter which has equipped with 2 type sparger is used to study the effect of sparger type and liquid height at different superficial gas velocity on total gas hold up. The results show that increasing liquid height and decreasing sparger hole diameter increase the gas hold up.

    Keywords: Bubble Column, Gas Sparger, Gas Hold Up}
نکته
  • نتایج بر اساس تاریخ انتشار مرتب شده‌اند.
  • کلیدواژه مورد نظر شما تنها در فیلد کلیدواژگان مقالات جستجو شده‌است. به منظور حذف نتایج غیر مرتبط، جستجو تنها در مقالات مجلاتی انجام شده که با مجله ماخذ هم موضوع هستند.
  • در صورتی که می‌خواهید جستجو را در همه موضوعات و با شرایط دیگر تکرار کنید به صفحه جستجوی پیشرفته مجلات مراجعه کنید.
درخواست پشتیبانی - گزارش اشکال